Products compatible with the Technics SL1200 and SL1210

All these Plates and armboards are manufactured from military spec Aluminium to extremely tight tolerances with a high quality satin finish.

Below is our standard off the shelf range but we have also manufactured special Mounting Plates for the Technics SL1200 and SL1210 to suit the following arms - Hadcock GH242, ADC, Grace 707, and Audio Technica AT1005 please contact us if you have a non standard requirement. 

As there have been many variations of Technics Turntables please check that your Deck has an Armboard recess diameter of 120 MM and attaches by 3 screws before ordering one of the following products. May not be suitable for the SL1200 MKI.

  SME 3009 Armboard for the SL1200 and SL1210

Technics SL1200 / SME
Technics SL1210 / SME3009 Armboard

For the fitting of an SME 3009 Tone Arm, locates the arm at the correct geometry and VTA (Vertical Tracking Angle). Comes with Screws for fixing the arm to the Plate and Plate to the Turntable.

Click here to buy

 
Armboard for mounting latest 9 " SME arms onto the SL1200 and SL1210
 

 Technics SME Armboard
 
For mounting the latest SME 9 inch arms on the SL1200 and SL1210 in the correct position, the arm mounting holes in this Plate are threaded to a larger size to suit the screws supplied with the later SME arms. Suitable for SME Series M2, Series 300, Series IV and Series V.  Comes with screws for fixing Plate to the Turntable only.  
 
 
 
 
Rega RB250 / RB300 Armboard for SL1200 and SL1210

 

Technics SL1200 / Rega Armboard
 

 
 
Technics SL1210 / Rega Armboard RB300
 
A Plate to allow fitting of a Rega RB 250, RB300 or RB600 at the correct geometry and VTA (Vertical Tracking Angle) Plate is also compatible with Rega based arms from Origin Live, Michell etc and also the Roksan Tabriz. Compatible with our VTA set and Speed nut if you require fine tuning of VTA.
 
 

 Rega 3 point arm (RB251 & RB301) Mounting plate for SL1200 / SL1210

Technics SL1200 Rega RB251 Armboard Technics SL1210 / Rega RB251 Armboard

This Plate is designed for mounting the new Rega 3 point type Tone arms at the correct position.  Suitable for use with Rega models - RB251 / RB301 / RB700 and RB1000 and other makes of arm that are based on these models. Compatible with our  VTA Shim Set for extra fine tuning of VTA. Comes complete with screws for mounting the arm to Plate and Plate to turntable.

Click here to buy   

Linn Armboard for the SL1200 and SL1210

Technics SL1210 / Linn

For fitting all Linn arms at the correct geometry and VTA (Vertical Tracking Angle) Also suitable for the straight armtube Jelco models. Screws for fixing Armboard to turntable are included.

 Click here to buy 

Jelco Armboard for the SL1200 / SL1210

 

Technics SL1200 / Jelco Armboard Technics SL1210 / Jelco Armboard

A Mounting Plate for locating the S shaped arm tube type Jelco arms which require a mounting distance of 214 MM.  Suitable for models SA-250 (not ST) and SA750D. Includes screws for securing the Plate to the deck.

Click here to buy